Fire Pump with Vertical Single-Stage

Product Description

Product Description

 

Products Name: UL listed fire pump with Vertical Single-Stage

Overview:

XBD vertical single-stage fire pump set is based on our IS type pump, combined with the characteristics of foreign pipeline pump, optimization design and manufacture of a new generation of products by itself. Use of fire hydrants in the water, feeding sprinkler system water supply in other occasions cleaning liquid.

Conditions of use:

1. XBD vertical single-stage fire pump set is used for transporting ambient water.
2. The water does not contain corrosive substances and solid particles.
3 Minimum working pressure 0.3Mpa, the maximum working pressure of 1.6 Mpa.
Characteristics of XBD vertical single-stage fire pump products

4, the pump is a vertical structure, import and export of the same caliber, and are in the same center line, as the valve can be installed in the pipeline, compact appearance, small occupation area, low construction inputs, such as protective cover can be placed outdoors
5, the impeller mounted directly on the motor lengthened shaft, short axial dimensions, compact structure, pump and motor bearings reasonable configuration, can effectively balance the pump running the radial and axial load, so as to ensure the operating balance vibration noise of the pump is very low.
6, seal mechanical seal mechanical seal or a combination, the use of imported titanium alloy seal ring, medium and high temperature mechanical seal with cemented carbide materials, wear-resistant, can effectively increase the service life of mechanical seal.
4, convenient installation and maintenance, no need to open the pipeline system, remove the pump as long as the union nut can block out all the rotor parts.
5, can be used according to the requirements that need to flow and head of the pump series, parallel operation.
6, according to the requirements of piping layout using the vertical and horizontal pump installation.

Performance requirements of fire pump is:

1. Maximum flow fire pump shall be 150% of the value of the design, the head is not less than the selected operating point of 65% lift, lift off the pump when not greater than the selected operating point of 140% lift, pump flow 1 2LS, head 1.1 - 1.2 times the fire pump lift.
2. At the same time in the fire pump outlet pipe should be located on measurement flowmeter, flow meter should be able to test 175% of the pump flow rate selected, fire pump pressure gauge set should be greater than 89mm in diameter at the outlet pipe.

fault phenomenon	failure cause	elimination methods
	1.No power supply or one or two phase power supply is needed	Check all phases of power supply and restore power supply
	2.Poor contact of ac contactor and burning of coil	Repair or replace contactors
can not start	3. The power switch is not closed, malfunction or damaged	Close the switch and replace it if the power indicator does not turn on
	4. Thermal relay trip or damage	Check whether the motor is blocked, find out the reason and eliminate it.Manual reset is replaced if it cannot be started
	Water level is too low	Put water in the sink
	The motor burned	Repair or replace the motor
	1.Line is loose	Check wiring and tighten connectors
	2.Frequency converter malfunction	Check the fault content, check the cause according to the frequency converter manual, and restart after reset.Or disconnect the inverter power supply for a few seconds, the inverter fault reset before starting.
The manual is normal	3The frequency converter is damaged	Repair or replace
Automatic transmission failure	4.Pressure switch damage	Repair or replace
	5The pressure transmitter is damaged	Repair or replace
	6.Switch failure	Repair or replace
Pump non - suction pressure gauge pointer to beat violently	Insufficient water supply for perfusion, air leakage at the connection between pipeline and instrument	Check pipeline and bottom valve, refill water diversion. Tighten air leakage
The pump consumes too much power	Too much flow, impeller wear	Check whether the pump shaft is bent, replace the impeller, close the outlet valve to reduce the flow

♦ ESTABLISHED IN THE SIXTIES


♦ ONE OF THE FIRST THROUGH THE ISO9001:2008 DOMESTIC,

INTERNATIONAL QUALITY SYSTEM CERTIFICATION


♦ SILVER MEDAL WAS AWARDED AT THE NATIONAL CONFERENCE ON THE

APPLICATION OF SPARK CUP TECHNOLOGY


♦ WIN THE NATIONAL AWARD FOR EXCELLENCE IN CIVILIZATION COMPETITION 


♦ GET THE LC OF THE CHINESE GOVERNMENT